Top 10 typical forklift mishaps ， forklift operation ought to take note of these matters ！.

Top 10 typical forklift mishaps ， forklift operation ought to take note of these matters ！.

Blog Article

Do not ignore the forklift at work. If the operation is not good, there will certainly be significant crashes in minutes, and there are many mishaps involving forklifts.

Instance 1: The forklift freight obstructed the chauffeur's sight, and the individual in front could not be discovered, causing a moving accident.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the staff members used their body weight as the counterweight, which nearly caused casualties.
Instance 3: The width of the forklift cargo goes beyond the permitted size of the route and holds on the roadside rack, which practically triggers an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Case 6: The forklift raises the workers unlawfully, the forklift chauffeur does not put on the safety belt, the forklift lifter drops and the motorist is squashed when the forklift surrender.
Case 7: The forklift motorist did not put on a safety belt and dropped from the automobile when it surrendered and was squashed.
Forklift procedure need to pay attention to these matters ：.

Begin.
1. Prior to starting, observe the surroundings, and after verifying that there are no barriers that prevent the safety of driving, honk the horn first and then start.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge should be secure before beginning.
3. When the forklift starts with a load, the driver must first validate that the tons is secure and trustworthy.
4. The begin must be slow-moving and stable.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the mast needs to be slanted backwards. .
2. Do not raise the fork expensive when driving. When going into and leaving the job site or while driving, take care that there will certainly be no barriers overhead. When the tons is traveling, the fork should not be elevated expensive, which will affect the stability of the forklift. .
3. After dumping, the fork should be decreased to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles nearby, the driving signal should be issued initially. High-speed sharp turns are prohibited. High-speed sharp turns will certainly cause the car to lose side stability and topple. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with lots unless there are unique situations.
6. When the forklift is running, it has to obey the web traffic rules in the factory and need to keep a certain safety range from the automobile in front. .
7. When the forklift is running, the load needs to be in the lowest placement that does not impede the driving, and the gantry ought to be correctly slanted back. The tons will not be raised except when stacking or loading. .
8. The elevation of the lots have to not obstruct the driver's view. In special conditions, when the thing impacts the forward vision, drive at a low speed when turning around.
9. It is forbidden to switch on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving rate of the forklift in the factory area is 5 km/h, and it needs to drive safely at a reduced rate when entering the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is forbidden for workers to stand on the fork to hold products and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a prompt fashion, and they will never run with ailments or conceal them.

packing and unloading.
1. When fork-loading things, the range in between both forks need to be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the item need to protest the shelf. .
2. It is prohibited to collaborate with a solitary fork or make use of a fork top or pull. In unique scenarios, safety and security indication should be established to advise surrounding pedestrians. .
3. In the process of filling and unloading things, the forklift should be braked with the brake. .
4. The rate of the car must be slow-moving and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be noted that the fork tip need to not touch other items or items. The load should be stabilized with minimal back tilt of the gantry to make sure that the tons does not glide backwards. The mast can be slanted forward a little when the tons is reduced to enable very easy placement of the lots and removal of the forks. .
6. It is restricted to fork items at high speed and ram hard objects with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure people. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift personnel to engage in high-altitude operations to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slip, put, round or roll things. .
10. It is not allowed to utilize forks to choose, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or lower the fork structure.
2. Pull the parking brake handle to dead or dispirit the hand brake switch.
3. The engine is turned off and the power is cut off. (Except for special scenarios, such as the chauffeur does not leave the vehicle's view and does not surpass 1 minute).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance needs to be checked, and gas, lubricating oil and air conditioning water ought to be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and reliable.
4. During the procedure of the forklift, check whether the stress and temperature are normal.
5. After the forklift is running, the exterior leakage must likewise be inspected and the seals ought to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the car;.
2. When you encounter somebody before you during driving, you must send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the freight need to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be also sharp to prevent the tendency of " totally free switching";.
6. Running up and down the incline must be slow and consistent, and no switching on the incline is enabled.
7. Do not drive across the gradient. When the gradient is more than 10%, the car must be driven in reverse when worsening;.
8. When the forklift employees lug the goods and progress, if they experience huge or heavy items and go to the driver's line of vision, they ought to take the turning around Electric Forklift Truck for Warehouse exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork procedure is not enabled.
2. It is not permitted to raise the goods for far away driving.
3. It is not enabled to pick up the goods by turning over the pallet with the fork.
4. It is not allowed to straight shovel Stand-on Electric Pallet Stacker chemicals, flammables and other harmful chemicals with forks.
5. It is not enabled to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is raised.
8. Do not drive side to side on inclines
.
Car parking is not allowed under the list below conditions.
1. Contours, narrow roadways, train crossings;.
2. Areas with a longitudinal incline above 5%.
3. When there is an obstacle on one side of the roadway, the opposite side of the area with the same size as the barrier ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844